A tarpaulin almost never fails in the middle. It fails at the edge — a grommet tears out of the hem, the hem itself pulls away from the cloth, or the hole elongates until the rope slips through. That is why the edge specification, which is three numbers long, matters more to the life of a cover than the difference between 180 and 200 GSM.
We build the edge in-house as part of eyelets and finishing, and buyers who come from the retail side are usually surprised by how much of the price sits there. This page is the specification vocabulary: what the parts are called, which numbers are actually comparable, and how the spacing should change when the load does.
Grommet, eyelet, tie-down: three words, one edge
The terminology is used loosely across the trade, so start with the components rather than the names. A grommet is a two-piece metal ring pressed through a hole in the hem: a barrel that passes through the cloth and a washer that rolls over it. An eyelet is the same idea at smaller size, usually without the rolled washer, and it is what you find on curtains and light awnings. A tie-down is not part of the tarp at all — it is the rope, cord, bungee or strap that passes through the hole.
The practical distinction is that a grommet is designed to take a lateral pull from a rope, and an eyelet is designed to hold a small hook. Put a tensioned rope through a curtain eyelet and it will cut through the coating. If a supplier’s quote says “eyelets” on a cover that will be roped down outdoors, ask for grommets and a washer.
The three numbers that decide everything
- Inside diameter (ID) — how big the hole is, in millimetres. This has to suit the rope: too small and the rope binds and wears, too large and the load concentrates on a thin ring of cloth.
- Spacing — the distance between hole centres along each edge. This sets how many points share the wind load, and therefore the load per hole.
- Set-back — the distance from the hole centre to the edge of the cloth, and to the corner. Too close and the hem tears out; too far and the corner flaps.
Those three, plus the metal (brass, stainless, or aluminium) and whether the hem carries a rope or reinforcing tape, fully describe an edge. Everything else — the “#4 grommet” style labels, the “heavy duty” adjective — is either redundant or unverifiable.
Grommet sizes: why the # numbers don’t travel
Suppliers refer to grommets as #1, #2, #3 and so on, and the numbering is not consistent between manufacturers. A #4 from one press may be 5/8 in (16 mm) and from another 3/4 in (19 mm). For a purchase order, specify the inside diameter in millimetres and ignore the number.
| ID (mm) | ID (in) | Fits | Typical use |
|---|---|---|---|
| 10–12 | 3/8 – 1/2 | 4–6 mm cord, small hooks | Light covers, dust sheets, market stalls |
| 16 | 5/8 | 6–8 mm rope, ball bungee | General covers, stockpiles, trailer loads |
| 20 | 3/4 | 10–12 mm rope, ratchet strap hook | Large covers, screening, site hoarding |
| 25 | 1 | 12–14 mm rope, shackle | Marine and container work, heavy tension |
The metal matters less than buyers expect and more than suppliers admit. Brass is the default because it presses cleanly and does not gall; stainless is worth the premium on marine and coastal work; aluminium is light and cheap and deforms under sustained load. In a salt atmosphere, a brass grommet and a galvanised rope will corrode against each other, and the hole is where it starts.
Spacing: 24 inches is a default, not a rule
The retail convention is a grommet every 24 in (600 mm) on all four edges, with one in each corner. That is fine for a cover that sits on a stack and is weighted down. It is not fine for anything that faces wind as a surface, because the load per grommet scales with the area each one is holding.
Do the arithmetic once and the rule stops being arbitrary. Wind pressure is roughly q = 0.00256 × V² in pounds per square foot, with V in mph. At 50 mph that is 6.4 psf. A 6 × 50 ft screen has 300 ft² on one face, so about 1,900 lb — 870 kg — of load, shared across the grommets on the windward edges. At 24 in spacing that is roughly 100 kg per grommet. At 12 in spacing it halves.
That is why screening and hoarding go to 12 in (300 mm) or tighter, and why the same cloth that lasts five years as a stockpile cover fails in one season when it is used as a windbreak. The failure is at the hole, not in the fabric. If a cover is going to be exposed as a surface, halve the spacing and add a reinforcing patch at every corner before considering a heavier cloth — the fence and screening page has the full load table.
How the hem is built is half the specification
A grommet is only as strong as the cloth around it, and the cloth around it is a folded hem. The standard build is a double fold 1–2 in deep, welded or stitched through, with a reinforcement patch at each corner and — on anything above light duty — a rope or a polyester tape laid inside the fold so the load is carried by the rope rather than by the coating.
Two details separate a good edge from a cosmetic one. The first is whether the hem is welded or stitched: welded is stronger and fully waterproof but cannot be repaired in the field, stitched can be re-sewn anywhere and leaks at every needle hole unless the seam is also taped. The second is corner construction. A corner takes load from two directions at once, which is why it gets a patch, and why asking for “double grommets in each corner” is a reasonable substitution when a patch isn’t available.
Clips and bungees: retrofit, not specification
Spring clips and ball bungees are the most-searched items in this whole subject, and they solve a real problem: attaching a cover to a frame that has no matching grommets, or adding a tie point where the spacing is wrong. A clip grabs a fold of cloth and gives you a hole; a ball bungee gives you a loop that will not rattle loose.
Both are retrofit solutions and neither belongs in a volume specification. A clip concentrates load on a small patch of unsupported cloth and will tear a light tarp at the first hard gust; a bungee that is stretched to its limit loses tension and lets the cover flutter. If a cover needs more tie points than it has, the fix is a different edge spec, not more clips. We supply the cloth and the edge — we do not sell the hardware, and a quote that bundles clips is usually a distributor’s quote rather than a mill’s.
What to put in the spec
For a purchase order, six lines are enough:
- Grommet ID in mm, and metal (brass / stainless / aluminium).
- Spacing in mm, and whether it changes on the long edges.
- Set-back from the edge, or simply “standard” if you accept the mill’s default.
- Hem type: fold depth, welded or stitched, rope or tape inside.
- Corner treatment: patch, double grommet, or both.
- Any second row of holes, and where — a cover that will be laced to a frame needs holes on two axes, not one.
Humanitarian and institutional buyers often skip this conversation entirely by specifying a published standard — the IFRC tarpaulin specification, for instance, fixes the cloth weight and puts the eyelets on a one-metre grid — which is a much faster way to get comparable quotes. Commercial buyers rarely have that luxury, and the six lines above are the next best thing.


