A “standard” tarp size is not a manufacturing standard. It is a retail convention — the sizes that American hardware chains decided to stack on shelves in the 1970s, later copied by everyone else. Nothing about a loom, a coating line or a welding table requires a tarp to be 10 × 12 feet. That matters because most buyers who search for a size chart are not shopping for a shelf product: they are trying to work out whether a stock size will cover the thing in front of them, or whether they need one cut to order.
We cut tarpaulin sheets to finished size rather than shipping a fixed catalogue, which means the useful question is never “what sizes do you have” but “what is the smallest standard size that covers my span without wasting a third of the cloth”. This page answers that: the sheet sizes the market treats as standard, the roll widths that decide how many seams your cover needs, and the three measurements that let you specify a custom size in one email.
Standard sheet sizes, in feet and metres
The list below is what appears in most retail and distributor catalogues. The metric column is the arithmetic conversion, not a separate product line — 20 × 30 ft is a 6.1 × 9.1 m tarp, and it is ordered as one or the other depending on where you sell.
| Nominal size (ft) | Metric (m) | Area (m²) | Typical use |
|---|---|---|---|
| 6 × 8 | 1.8 × 2.4 | 4.4 | Pallets, small equipment, firewood bays |
| 8 × 10 | 2.4 × 3.0 | 7.3 | Single pallet stacks, garden use |
| 10 × 12 | 3.0 × 3.7 | 11.1 | One-car cover, small boat, wood pile |
| 12 × 16 | 3.7 × 4.9 | 17.9 | Trailer loads, small shed roof |
| 16 × 20 | 4.9 × 6.1 | 29.7 | Flatbed loads, temporary roofs |
| 20 × 30 | 6.1 × 9.1 | 55.7 | Container-top, machinery, hay bays |
| 30 × 50 | 9.1 × 15.2 | 139.4 | Large stockpiles, silage, site screening |
Two things in that table are worth arguing with. First, the sizes are nominal: a 20 × 30 tarp is not 20.000 × 30.000 feet. Cut tolerance on a welded sheet is normally ±2 in on each dimension, and the finished size is measured over the hem, not over the raw cloth. Second, the jump from 16 × 20 to 20 × 30 is not arithmetic — it is a factor of nearly two in area, which is why buyers covering something in between end up paying for cloth they never unfold.
Roll widths decide the seam count, not the length
On a roll, length is free and width is not. Cloth comes off the line at a fixed width, so a cover wider than one panel has to be joined — and every join is a welded seam with a weld bead, a heat-affected zone and a labour cost. Length, by contrast, is simply cut at whatever point you stop unrolling. This is why two covers with the same area can have very different prices.
The single-panel widths we run are 2.0 m and 4.0 m on polyethylene, and 3.2 m, 4.0 m and 5.0 m on PVC-coated polyester. A tarpaulin roll is therefore specified by width plus running metres, not by a fixed length, and the buyer who works in feet should convert width first: 6.6 ft, 13.1 ft, 10.5 ft, 13.1 ft and 16.4 ft respectively.
| Finished width | PE (2.0 / 4.0 m panels) | PVC (3.2 / 4.0 / 5.0 m panels) |
|---|---|---|
| 20 ft (6.1 m) | 2 panels · 1 seam | 2 panels · 1 seam |
| 24 ft (7.3 m) | 2 panels · 1 seam | 2 panels · 1 seam |
| 30 ft (9.1 m) | 3 panels · 2 seams | 2 panels · 1 seam |
| 40 ft (12.2 m) | 4 panels · 3 seams | 3 panels · 2 seams |
Read that table before comparing two quotes for the same size in different materials. A 30 × 50 ft cover is two seams in PVC and two seams in PE — but the PE one is built from three narrower panels, so the same finished size hides a different amount of welding. If a supplier quotes 30 ft in both materials at the same labour line, one of the two numbers is a guess.
Cut size, finished size, and the 2 inches that go missing
Every edge on a finished tarp is folded. A standard hem is a double fold about 1 in deep, sometimes with a rope or a reinforcing tape inside it, and it is stitched or welded through. That fold consumes cloth on all four sides: roughly 2 in per edge, so 4 in off each dimension, or about 10 cm. On a 6 × 8 tarp that is a 5% loss of area; on a 20 × 30 it is negligible. On a small cover where the fit is tight, it is the difference between covering the object and not.
The same applies to grommets. A grommet sits in the hem, and the hem has to be wide enough to hold it. If you ask for grommets every 24 in right up to the corner, the corner still needs enough hem to take a grommet without tearing out under load — which is why corner reinforcement patches exist and why a quote that includes “grommets every 2 ft” without mentioning corners is incomplete.
The three measurements that replace a size chart
For anything that is not a flat rectangle on the ground, the size you need is not the footprint. It is the footprint plus the drop on every side that has to hang. Measure the span (the widest horizontal distance the cover must bridge), the drop (how far it must hang down each side), and the slope (whether the top is flat, pitched or arched). Those three numbers plus a note on what the cover touches are enough to quote.
Some worked examples, because this is where most sizing emails go wrong:
- Round pool, 15 ft diameter (a common search: what size tarp for 15 ft round pool). The cover has to overlap the wall, so add twice the overhang to the diameter: 15 ft plus 2 × 2 ft gives 19 ft, and the next workable size is 20 ft round or a 20 × 20 square with the corners folded. See pool tarpaulins for why an above-ground pool also needs the wall covered, not just the water.
- Round pool, 18 ft diameter: 18 ft plus 4 ft overhang is 22 ft; a 24 ft round or a 24 × 24 square is the practical order.
- Car (what size tarp to cover car): a mid-size sedan is about 15 ft long and 6 ft wide. For a cover that drapes to the sills, 16 × 20 ft is the smallest sensible size; anything smaller will not reach both bumpers with cloth left to tie.
- Flatbed load (flatbed tarp sizes): the tarp has to cover the deck plus both sides plus enough to tuck, so a 48 ft deck needs roughly 48 × 8 ft of top plus 2 × 4 ft of side drop — specify by deck length, and see truck and trailer tarpaulins for the tie-down layout.
- Roof (roof tarp sizes): never buy the roof area. Slope factor, ridge overlap and anchor margin together add 25–40% to the plan area; the roofing page covers the arithmetic.
When the standard size stops working
A standard size stops being the cheap option at two points. The first is when the cover is more than about 15% larger than the object: you are paying for cloth that flaps, and flapping cloth fails at the grommets long before the fabric wears out. The second is when the object is a shape rather than a rectangle — a hopper, a machine housing, a container top with a camber. Cutting a rectangle down and welding it back together costs more than cutting to shape in the first place.
That is the entire argument for a custom size, and it is a boring one: the price difference between a stock size and a made-to-size sheet is usually smaller than the cost of the wind damage a loose cover causes. It is not, however, an argument for a custom size on a 10 × 12 pallet cover, where a stock size is genuinely cheaper.
What to put in the email
One paragraph is enough, and it saves two rounds of clarification:
- Finished size, in feet or metres, and say which — do not mix. If you know the cut size you need instead, say so explicitly.
- Material and weight, or the job it has to do. “PE, 200 GSM, for a stockpile” gets a quote; “heavy duty” does not.
- Edge spec: hem type, grommet spacing, whether corners need reinforcement, and whether you need rope in the hem.
- Quantity and destination, because 5 tonnes of one size prices differently from 5 tonnes split across four sizes — our minimum applies per specification, not per order.
Standard lead time is 30 days per container for stock specifications; a new cut size adds pattern and setup time but not a new minimum, provided the material and weight are already running. Samples are free with freight collect, which is the fastest way to settle a “will 200 GSM be enough” argument before committing to a container.


