Opens in a new tab
ROC Tarp HomepageGet a Quote

Truck & Trailer Tarpaulins

Truck tarps are specified by their drop, not by the trailer's length. Get the drop right and the sheet sits on the load instead of flapping above it; get it wrong and no amount of strap tension saves it. The job decides the weight, the drop and where the reinforcement goes. We cut and weld to North American trade sizes — 24×27 with 8×8 drops, 20×27, three-piece sets — in coated PE from 50 to 300 GSM on our own lines, and in 18 oz PVC-coated polyester to the same drawing. D-rings, webbing and grommet spacing follow your drawing, not a stock pattern.

Flatbed, dump and trailer covers

PVC 18 oz Black Lumber Tarp 24×27 ft

The North American lumber tarp size. 24 x 27 with an 8 x 8 drop covers a standard flatbed load with the ends hanging past the stake pockets.

Material
PVC
Weight
18 oz / 610 GSM
View product
Buying guide

How to specify a flatbed tarp: drop first, then fabric

Most truck tarp enquiries arrive with the trailer length and nothing else. Trailer length is the one number that barely matters. What decides whether a cover works is the drop — how far the fabric hangs down the side of the load — because that is what sets the fabric weight, the D-ring rows and whether the sheet can be tensioned at all.

Match the cover to the load

Load Cover type Typical drop Fabric Why
Lumber, plywood, building materials Lumber tarp 6–8 ft 18 oz PVC Tall load, fabric dragged over board ends
Steel coil, plate, pipe Steel tarp 4 ft 18–22 oz PVC Low profile but highly abrasive edges
Machinery, oversized freight Lumber tarp or custom 6–8 ft 18 oz PVC Irregular shape, needs corner reinforcement
Front face only Smoke / nose tarp 4–8 ft deep 18–22 oz PVC Exhaust soot and road spray only
Dump body, aggregate Dump cover n/a 200–300 GSM PE Consumable, replaced before it wears through
Hot-mix asphalt Dump cover n/a Heat-resistant fabric Heat plus abrasion — outside our range, read section 3
Lorry, cargo, curtain-side Lorry sheet Trailer height 200–300 GSM PE Manual handling, weight beats abrasion
Refuse, mulch, scrap Mesh cover n/a Leno mesh Must not hold water; wind pass-through

1. Flatbed tarps: the drop is the specification

A flatbed tarp is named by its footprint and its drop. A 24×27 with 8×8 drops is the standard lumber tarp: 8 ft of side drop and 8 ft of end drop, enough to close a load 8 ft tall and 8 ft across. Drop the sides to 6 ft and you have a 20×27, which is the same tarp for a lower load. Drops of 4 ft make it a steel tarp — the fabric only has to cover the top and the top corners of a coil or plate load.

So the question is not “how long is my trailer” but “how tall and how wide is the load, and how much do I want hanging past the deck edge”. Send us those two figures and the tarp size follows arithmetically. That is also why two truck tarps in the same nominal size can differ by 30% in finished weight — the drop did the work, not the length.

One tarp or a set?

Full-deck loads take two tarps or a three-piece set: two end pieces plus a middle section, which is easier to handle alone and lets you replace the worn middle without scrapping the ends. Short or partially loaded decks take a single tarp. Drop-deck and step-deck trailers carry low loads on a longer, narrower deck, so they usually want the opposite shape: longer and shallower — a 28×16 rather than a 24×27.

Lumber tarps, steel tarps, smoke tarps

These are not three products, they are three drop heights and three levels of abrasion. A lumber tarp is the tall one. A steel tarp is short but heavier per square metre, because steel coil edges and plate corners cut through fabric that has any give in it. A coil tarp is the same sheet cut narrower again, usually with a double layer where the coil sits. A smoke tarp — sometimes called a nose tarp — covers only the front six to eight feet, for loads where the rear is already weatherproof and only the front face collects exhaust soot and road spray.

From three measurements to an order size

Input How to get it Example
Load height Deck to the top of the load, in feet 8.0 ft
Side drop Load height, plus 1–2 ft of overhang 8.0 ft
Load width Measure the load, not the deck 8.0 ft
Tarp width 2 × drop + load width 24.0 ft
Length to cover Front to back of the load 24.0 ft
Size to order Width × length, rounded to the trade size 24×27
Pieces One for a short deck; two or a three-piece set for full length 1 or 3
Flat weight Area in m² × GSM ÷ 1000 60.2 × 0.61 = 37 kg
Finished weight Add 30–35% for drops, hems and reinforcement ≈ 50 kg

2. 18 oz PVC or coated PE? This is the decision that matters

In North America the flatbed trade settled on 18 oz (610 GSM) PVC-coated polyester, 1000D, 18×18 or 20×20 weave — part of our PVC range — with 14 oz for light loads and 22 oz for abrasive steel. That is a heavy, stiff, highly abrasion-resistant sheet with cold-crack resistance to about −40 °C. It is not the same material as a coated PE tarpaulin and it should not be priced as one.

Our own plant runs coated PE from 50 to 300 GSM — a far lighter fabric. Where does that belong on a truck? Three places, and they are real ones:

  • Lorry and general cargo covers in markets where a 37 kg sheet is unmanageable for a two-man crew. A 250 GSM PE cover over the same 24×27 footprint weighs about 15 kg. It goes on and comes off without a machine.
  • Dump and roll-off covers, where the fabric is a consumable that gets replaced long before it wears through — light weight and low replacement cost beat abrasion life.
  • Temporary and seasonal covers, single-season use where the tarp is discarded with the load or the job.

Where PE does not belong: dragged daily over steel coil edges, over lumber ends, or across a deck with rough welds. Abrasion, not sunlight, is what kills a flatbed tarp, and 18 oz PVC simply has more material to lose. We will tell you which of the two lines your application actually needs rather than quote the cheaper one and let you find out. If even 22 oz looks marginal for the abrasion you are seeing, that conversation moves to heavy-duty covers rather than to a lighter sheet.

The range both lines cover

Property What we work to
Coated PE (own lines) 50 – 300 GSM (1.5 – 9 oz/yd²)
PVC-coated 14 – 22 oz (475 – 745 GSM)
Yarn 600D – 1500D (PE) · 1000D (PVC)
Weave density 6×6 – 16×16 (PE) · 18×18 – 20×20 (PVC)
Duty classes Light 50–90 / Medium 90–160 / Heavy 160–300 GSM
Trade sizes on file 16×27 · 20×27 · 24×27 with 4–8 ft drops; 28×16; three-piece sets
Fixings D-rings at 24 in as standard, rows and spacing to your drawing
Seams and edges Heat-welded seams, 2 in hem with 2 in webbing, reinforced corners
Single-piece width PE 2.0 / 4.0 m · PVC 3.2 / 4.0 / 5.0 m (no seam)
Seams across 24 ft (7.32 m) PE 4 m → 1 seam · PVC 5 m → 1 seam
Seams across 16 ft (4.88 m) PE 4 m → 1 seam · PVC 5 m → 0 seams
Format Finished covers, or roll material for fabricators

The 16 ft figure is the one worth pausing on. A 24 ft width is two panels either way, so there is no advantage to PVC there. At 16 ft the PVC width closes in one piece and the PE width does not — and a lengthwise seam is the first place a cover lets water through.

3. Dump truck tarps, roll-offs and asphalt

A dump cover fails in two places: along the tailgate lip, where the load drags across the fabric every time it tips, and at the front, where the sheet rubs on the cab shield. Both are abrasion problems, so the fabric needs mass and the reinforcement needs to be where the wear is, not spread evenly around the perimeter. A dump trailer tarp is cut to the same logic — the difference between a dump truck tarp and a dump trailer tarp is the body it sits on, not the fabric.

Asphalt is its own case, and it is the one place where we will talk you out of the obvious answer. Hot mix leaves the plant at 150–165 °C. The PVC we supply is rated to about 70 °C continuous contact. Those two numbers do not meet, and no amount of extra grams per square metre closes the gap — a heavier sheet is still the same polymer.

Which is why asphalt covers in practice are specified around the heat rather than through it: the sheet is kept off the hot material by the body or a liner, it is only pulled over once the load has crusted, or the application uses a heat-resistant coated fabric that sits outside our range. If you are covering hot mix straight from the plant, say so in the enquiry and we will tell you honestly whether we can supply it. If you are covering milled asphalt, cold patch, or a load that has cooled on the run, standard 18–22 oz PVC is the right sheet and it will last.

What we will not do is print a temperature rating that flatters the product. The failure mode is silent — the coating softens, the weave takes the load, and the sheet fails on a motorway rather than in your yard.

One thing we do not make: the arms, motors and rollers. If you run a roll-tarp or pull-tarp system, we supply the replacement sheet that fits it and you keep the hardware. That is usually the cheaper path anyway — the mechanism outlives three or four covers.

Where the load must not hold water — refuse, mulch, scrap, hot aggregate that steams — a mesh cover is the right answer, and our leno and mesh range is woven in-house.

4. Trailer tarps, semi-trailers and lorry sheets

Van trailers, curtain-siders and flat-deck semi-trailers in Europe, Africa and Southeast Asia are covered with what those markets call lorry tarpaulins or haulage covers: lighter, cut to the trailer’s own dimensions, often with a rope-reinforced hem rather than D-rings, and frequently in blue. The specification logic is the same as a flatbed tarp, but the handling is manual, so weight per square metre is driven down by labour rather than by abrasion. In North America the same covers are sold as trucking tarps or truckers tarps, and the flat-deck version of one is a semi tarp. The name moves with the buyer; the specification does not.

Cattle and livestock trailers are a small but distinct line — the cover has to vent, because a sealed sheet over live animals condenses and the load suffers. Mesh or vented panels, not solid coated fabric.

5. The hardware is where covers actually fail

Sheets rarely tear in the middle. They tear out at the fixing point, because that is where load concentrates. Four things to specify:

  • D-rings at your spacing. The North American convention is every 24 inches, which matches the strap spacing most states expect. We set the rows and the spacing to your drawing; if you say nothing we will ask rather than guess.
  • Webbing, not just a folded hem. A 2-inch hem with 2-inch seatbelt webbing run inside it is what stops an eyelet pulling through under tension. A plain folded hem looks the same in a photo and fails in service.
  • Heat-welded seams. A stitched seam is a line of holes; on a flatbed tarp it wicks water into the load and starts delaminating at the thread line. Every seam we make is welded, not stitched — the same cutting and heat-sealing operation that sets the eyelets. If the eyelet itself is the weak point on your current covers, the eyelet and hem build covers what sits behind it.
  • Reinforced corners and a tail flap. The rear is the first place wind gets under a sheet, and the corner is where the drop, the hem and the webbing all meet.

6. Working out weight and order quantity

Fabric weight ≈ area × GSM ÷ 1000. A 24×27 ft sheet is 60.2 m² of flat area, so at 18 oz (610 GSM) the flat rectangle alone is about 37 kg. The finished tarp is heavier — the drops and hems use more fabric than the flat rectangle — which is why a finished 8×8-drop lumber tarp comes out around 50 kg rather than 37. Budget on the finished figure, not the flat one.

Our minimum order is 5 tonnes. In 18 oz lumber tarps that is roughly 100 finished pieces — enough to fill a mixed container alongside other lines, or to split across three or four sizes. If you are a fabricator rather than a distributor, buying roll material and making up your own is usually the better route — tell us and we will quote both ways.

FAQ

Frequently asked questions

What size tarp do I need for my flatbed?

Measure load height, load width and load length — not trailer length. Tarp width is roughly twice the side drop plus the load width; a load 8 ft tall and 8 ft across with 8 ft drops needs a 24 ft wide tarp, which in the trade is the 24×27 lumber tarp. Send the three measurements and we will confirm the size and the finished weight.

Do I need a lumber tarp or a steel tarp?

Lumber tarp if the load is tall — 6 to 8 ft of side drop. Steel tarp if the load is low and flat but abrasive, like coil, plate or pipe: shorter drop, heavier fabric. If you haul both, most operators run an 18 oz lumber tarp and accept the extra material hanging loose on steel loads.

18 oz PVC or coated PE — which one should I buy?

If the cover is dragged over steel, lumber ends or a rough deck, 18 oz PVC. It has the mass to lose to abrasion and it stays flexible in cold. If the cover is handled by hand, replaced regularly, or used seasonally, coated PE at 250 GSM weighs about 15 kg over the same 24×27 footprint against 37 kg for the 18 oz sheet. We quote both and will say which one your application actually needs.

Can you make a three-piece set, or custom drops?

Yes. Drops, footprints, D-ring rows, grommet spacing and reinforcement positions are all cut to your drawing. Three-piece sets are the normal way we supply long-deck loads, because the middle section wears first and can be replaced on its own.

I already have the arms and rollers — can you supply just the sheet?

Yes, and it is usually the better buy. Send the dimensions your existing mechanism needs, or send the old cover as a pattern. We do not make tarp systems, motors or hardware — only the fabric part.

What D-ring spacing do you use?

Every 24 inches as standard, in the number of rows your drop needs, because that matches the strap spacing most road authorities expect. If your fleet uses a different pattern, we set it to yours — tell us at quoting stage, since it changes the webbing cost.

What is the minimum order and lead time?

5 tonnes per order. In 18 oz lumber tarps that is roughly 100 finished covers. Coated PE from our own plant runs about 30 days from deposit for a standard container order; PVC-coated covers run about 45 days, depending on how many specifications are in the order. Custom print is 5 tonnes per specification, because each colour needs its own masterbatch.

Can covers be branded or printed?

Yes — logos, load ratings, fleet numbers and edge marking. Artwork and shade approval are handled on our side, but printing is scheduled as a separate printing process, so it carries its own minimum quantity and its own lead time, both higher than a plain order. Raise it before you commit to a design.

Truck & Trailer Tarpaulins

Request a quotation

Leading PE tarpaulin factory in China. Specialized in manufacturing high-quality polyethylene tarpaulins.

  • what'sapp: +86 18561818308marketing@roctarpstarp.com
  • Get an instant quote