Opens in a new tab
ROC Tarp HomepageGet a Quote

Tarpaulin vs Canvas: When Canvas Is the Wrong Material

About 8 min read
Share

Search for a canvas tarp and you will be shown forty products that are not canvas. Search for a tarpaulin and you will be shown the same forty. The two words are used as if they were alternatives on the same shelf, and they are not: canvas is a fibre and a weave, while tarpaulin is a job description — a cloth that covers something. A canvas tarp is a tarpaulin made of cotton duck. A poly tarp is a tarpaulin made of polyethylene. Almost every confused comparison starts with that category error.

This matters here because we do not make canvas. We weave and laminate polyethylene tarpaulins, and cotton duck is not a product we can supply from any line. So this page is not going to pretend otherwise. What it will do is set out where canvas is genuinely the better cloth, where it quietly costs more than it looks, and how to tell which situation you are actually in before you spend money on the wrong one.

What canvas is, in the units buyers quote

Canvas is a plain-woven cotton cloth, sometimes with a polyester fraction blended in for strength. It is sold by weight per square yard, and the trade grades are 10 oz, 12 oz and 18 oz — roughly 340, 410 and 610 g/m². Above 18 oz you are into belting and hose duck, not covers.

The older numbering system runs from No. 1, the heaviest, to No. 12, the lightest, and no two mills agree on where the numbers fall. If a supplier quotes “No. 8 duck” without a weight, you have been given a name rather than a specification. Ask for oz/yd² and for the finished width, in the same email.

Set that against a woven PE cover at 200 GSM and the difference is immediate: the canvas is three times the mass for the same area. A 10 × 10 ft cover is 9.3 m², so it is 5.7 kg in 18 oz canvas and 1.9 kg in 200 GSM polyethylene. One person can fold and throw the second one. The first one is a two-person job, and it stays a two-person job every time it is moved.

“Waterproof canvas” is a treated product, not a material

Untreated cotton duck is water-resistant, and only while it is wet. The fibres swell as they absorb water and close the gaps in the weave, which is why an old, well-soaked canvas shed rain that a new one passed straight through. A dry canvas leaks at the weave and at every stitch line. That is not a defect; it is how the material works.

So a product sold as waterproof canvas has been treated, and the treatment decides everything else about it:

  • Wax — paraffin or beeswax worked into the cloth. Good water shedding, stiff in the cold, attracts dirt, needs re-waxing every few years, and it burns. Waxed canvas is a heritage product with heritage maintenance.
  • Oil — linseed or similar. Classic oilskin, excellent in continuous wet, darkens the cloth, can transfer to whatever it touches, and stiffens with age.
  • Polyurethane or fluorocarbon finish — the closest to a modern proofing. Light, clean, and it converts the cloth into something much closer to a coated fabric, with much of the breathability lost.

The pattern is consistent: every step that makes cotton shed water also reduces the breathability that made you choose cotton. If a supplier claims both full waterproofing and full breathability, one of the two claims is being used loosely.

Where canvas is genuinely the better cloth

Four cases, and they are real:

  • Hot work and sparks. Cotton chars and smoulders; it does not melt and drip. Polyethylene melts at the first contact with a hot slug and the molten polymer can carry the ignition to whatever is underneath. If the cover will sit near grinding, welding or a chimney, this is not a close call. (Proper welding blankets are treated canvas, silica or fibreglass — we make none of them.)
  • Condensation is the bigger problem. A coated PE cover is a vapour barrier. Over hay, timber, or cold machinery in a humid climate, the water that forms on the underside does more damage than the rain it kept out. Canvas passes some vapour; PE passes almost none. The real answer for those loads is usually a vented or open-weave construction rather than either solid cloth, but canvas is at least directionally right.
  • Abrasion on a rough edge, where the cover is dragged over stone, concrete or a sharp steel corner. Cotton duck takes abrasion better than a 200 GSM laminated cloth, which is a thin film over a grid.
  • Aesthetics and specification — heritage awnings, film sets, market stalls where a plastic sheet is not acceptable, and events where single-use plastics are banned by the venue.

If your job is on that list, you should buy canvas, and we will say so rather than quote you something that fails in month three.

Where it loses on a commercial job

Outside those four cases, canvas usually loses to arithmetic:

Mass. Three times the weight per square metre, on every handling, every freight kilo and every installation. On a container-load basis that is not a rounding difference.

Rot. Cotton is food. Folded damp and left for a fortnight, it mildews; mildew stains permanently and eats tensile strength. A PE cover folded damp is simply a PE cover. Storage discipline is a real cost, and it is usually invisible in a price comparison.

Seams. Canvas is sewn, full stop — there is no welding a cotton duck. Every seam is a line of needle holes, and on a treated cloth the seam is where water gets in first. A welded PE seam is a continuous bond with no holes at all.

Piece size. Canvas loom widths mean wide covers are built up from panels roughly 1.5 m wide, so a 10 m span carries six or seven seams. A PE cover is welded from 2.0 m or 4.0 m single-piece widths, and a PVC cover from 3.2 m to 5.0 m, so the same span carries two or three welds.

Cost. Treated 18 oz duck runs several times the price per square metre of a 200 GSM PE cloth. You are paying for breathability, spark tolerance and a natural fibre, and if you do not need those three things, you are paying for them anyway.

The comparison, on the numbers that decide it

Property Cotton canvas, 18 oz, treated Woven PE tarp, 200 GSM
Mass per m² ≈610 g 200 g
Water shedding Only after treatment; leaks when new and dry By construction — laminated both faces
Breathability Yes, reduced by the treatment Effectively none
Rot and mildew Yes — cellulose is food No
UV life Degrades; treatment does not stabilise the fibre Depends on the stabiliser package
Seams Sewn, needle holes Welded, continuous
Widest single piece ≈1.5 m panels 4.0 m
Field repair Sew or patch, hand tools Heat weld or patch
Sparks and hot work Chars, does not melt Melts and can drip
Relative cost per m² Several times PE Baseline

Read down the two columns and the pattern is not “better” and “worse” — it is two different sets of trade-offs. Canvas trades mass, rot and cost for breathability and spark tolerance. PE trades breathability and spark tolerance for waterproofness by construction, rot-proofness, weldable seams and a quarter of the weight.

How to tell which job you have

Three questions settle it faster than a spec sheet:

  1. Will water form under the cover? If the answer is yes and the load cannot take it, canvas is directionally right — or a vented construction in either material.
  2. Will there be sparks, hot slag or a flue within a metre? If yes, canvas or a purpose-made welding blanket. Never polyethylene.
  3. Does it have to move, fold, ship or be replaced on a schedule? If yes, the mass and the rot risk make PE the cheaper cloth over a season, and often over a single job.

If it is the third and not the first two, a 200 GSM laminated PE cover will do the work of an 18 oz canvas at a fraction of the handling weight, and where the span or the wind load is the constraint, a heavy-duty tarpaulin at 250–300 GSM covers the gap before you have to think about a coated fabric. For anything built to a drawing rather than to a size list, the made-to-measure covers route is the one that avoids buying a standard size and cutting it.

What we actually make, stated plainly

We do not weave cotton duck and we do not proof canvas. If you need canvas, buy canvas — from a mill that does it, with the weight and the treatment named on the order, and plan for re-treatment. What we make is polyethylene from 50 to 300 GSM and coated fabric from 475 to 745 GSM, both welded to a size, and the differences between those two are set out on the tarpaulin materials comparison page.

The reason to say this clearly is that a buyer who orders the wrong cloth does not come back. A buyer who is told “not us, and here is why” usually does — often with the job the other material was wrong for.

roctarp.com

Ready to start your project?

Bring your drawing and the requirements you want to review.

  • Drawing
  • Material
  • Quantity
Request a quote
PROJECT INQUIRY

Ready to start your project?

By submitting this form you agree to be contacted about your enquiry.

Leading PE tarpaulin factory in China. Specialized in manufacturing high-quality polyethylene tarpaulins.

  • what'sapp: +86 18561818308marketing@roctarpstarp.com
  • Get an instant quote