Opens in a new tab
ROC Tarp HomepageGet a Quote

How to Compare Tarpaulin Quotes: What the Price Covers

About 6 min read
Share

Ask three suppliers for a price on the same tarpaulin and you will usually get three numbers within 30 % of each other, and three products that are not the same product. One is 200 GSM, one is 250 GSM quoted at the same nominal size, one has eyelets every 24 inches and one every 12. Comparing those numbers directly is not a price comparison; it is a comparison of how much fabric each supplier decided to leave out.

The fix is arithmetic, not negotiation. Put every quote on the same basis — same size, same finished weight, same edge, same delivery term — and the differences that remain are the real ones. That discipline is also what makes a bulk order auditable from quotation to container.

Normalise size and weight first

Two quotes for a “24×27 tarp” can differ by 30 % in material content before anything else is considered, because the size on the quotation is the cut size and the weight is rarely stated at all.

Start with the finished weight per piece. A 24×27 ft sheet is 60.2 m² of flat area. At 250 GSM the flat rectangle is about 15 kg. At 610 GSM it is about 37 kg, and once drops and hems are counted — they use more fabric than the flat footprint suggests, typically 30–35 % more — the finished cover is around 50 kg.

That is the same footprint, in two products that differ by a factor of three in material. If a quote does not state GSM, you cannot tell which one you are being offered. Our weight chart converts GSM, mil, denier and oz so the figure can be checked against whatever unit the supplier used.

The six lines that move the price

Line What it changes How it hides
Fabric GSM and construction Material cost — the largest single item Quoted at “same size”, weight not stated; scrim and coating weights not separated
Coating weight Waterproofing, weldability, UV carrier Total GSM quoted without the split, so a heavy scrim hides a thin coating
UV stabiliser Service life outdoors Word “UV” without a loading figure or weathering data
Seam method Labour, and whether the seam leaks “Heat sealed” claimed on a stitched seam with tape over it
Edge build Eyelet count, hem type, reinforcement Spacing not stated; corner patches omitted
Packing and term Freight, handling, duty FOB compared against CIF or DDP

Five of those six are specification, not price. They can be fixed by asking, which is why a quotation that cannot answer them is not yet a quotation.

What “cheaper” usually means

When a quote comes in materially below the others for the same stated size, the difference is almost always one of five things:

  • Lower GSM at the same nominal size. A 180 GSM sheet and a 250 GSM sheet are the same 24×27 on paper and 30 % apart in material.
  • Thinner coating on a heavier scrim. Total weight looks respectable; the waterproof layer is the part that was reduced.
  • Fewer eyelets. At 24 in spacing a 24×27 cover carries roughly 50 holes around its 31 m hem. At 12 in it is about 100, and the cost difference is real — as is the wind performance.
  • Stitched instead of welded seams. Faster, and it wicks water along the thread line.
  • Narrower rolls. More seams per cover, more labour, but sometimes cheaper fabric — the two effects do not always net out in the buyer’s favour.

Any of those can be the right choice for a given job. A dump cover that is replaced every season does not need the same edge as a cover that sees highway speed. The problem is not cheap; the problem is cheap that was never declared.

Put the numbers on one basis

Three conversions settle most comparisons:

  • Per piece: area (m²) × GSM ÷ 1000 = flat weight, then add 30–35 % for drops, hems and waste.
  • Per square metre of finished cover: piece price ÷ finished area. This is the only figure that compares different sizes fairly.
  • Per kilogram: piece price ÷ finished weight. Useful for spotting a quote that is priced on a lighter sheet than the one specified.

Run all three on the same quote and a pattern appears: quotes that look close per piece often diverge per kilogram, and quotes that look expensive per kilogram are often the ones that included the finishing. The sizes guide has the standard footprints if a quote arrives in a size you did not ask for.

Incoterm and packing belong in the comparison

FOB, CIF and DDP are three different products from a cash-flow point of view. FOB leaves the freight, insurance, duty and destination charges with the buyer; DDP puts them in the price. A DDP quote that looks 25 % higher may be the cheaper one once freight is added to the FOB alternative — or it may be the one carrying an optimistic duty assumption.

Packing matters at container scale. Bales compress better than cartons, and a supplier who packs to your container rather than to a standard carton can move more pieces per load. That is a real cost difference per unit, and it never appears on a per-piece quote.

MOQ, colour and run length

Our minimum is 5 tonnes, and it applies per specification — per size, per colour, per construction. That is not an administrative detail; it is how coating and cutting runs are scheduled. Splitting 5 tonnes across three colours means three short runs, three set-ups and a higher unit cost than the same 5 tonnes in one colour.

The same logic explains why a custom size is not automatically more expensive than a stock size, and why a small addition late in the order — a different eyelet spacing, an extra patch — can move the price more than its material content suggests. If the specification is settled before the run is scheduled, most of that disappears.

Lead time is part of the price

Standard production runs about 30 days for coated PE, and about 45 days for PVC because a specification change restarts the coating run. Add transit, and the difference between two suppliers’ lead times can be the difference between catching a season and missing it.

Payment terms carry a cost too, and it is usually invisible. A 30-day sight letter of credit, a deposit-and-balance arrangement and open account terms are three different financing costs, and the cheapest unit price is often attached to the most expensive terms. Put both on the table at once.

The spec sheet that makes quotes comparable

Send this with the enquiry, and every reply comes back on the same basis:

  • Size, stated as cut size, plus drop dimensions if it is a vehicle cover.
  • Total GSM, and the scrim and coating weights if known.
  • Construction: woven and laminated, woven and coated, or unreinforced.
  • Colour, and whether it is a standard or a matched shade.
  • Seam method and seam direction.
  • Edge: hem type, eyelet diameter, spacing, corner reinforcement.
  • UV requirement, stated as a target service life rather than a label.
  • Packing: bale or carton, pieces per unit, marking.
  • Incoterm and destination port.
  • Quantity, and whether the 5 tonnes sit in one specification or several.

We would rather quote two options than one — the specification you asked for, and the lighter or heavier build that the application might actually need — because the most expensive quote is the one that was right on price and wrong on weight. Sending the ten lines above is the fastest way to get to that conversation.

roctarp.com

Ready to start your project?

Bring your drawing and the requirements you want to review.

  • Drawing
  • Material
  • Quantity
Request a quote
PROJECT INQUIRY

Ready to start your project?

By submitting this form you agree to be contacted about your enquiry.

Leading PE tarpaulin factory in China. Specialized in manufacturing high-quality polyethylene tarpaulins.

  • what'sapp: +86 18561818308marketing@roctarpstarp.com
  • Get an instant quote