Most flatbed tarp enquiries start with the wrong number. The buyer measures the trailer, quotes its length, and asks for a cover to fit it. The tarp is not sized to the trailer. It is sized to the load — and specifically to its drop, the distance the fabric hangs down the side.
That is why a flatbed or trailer cover is described in two numbers that have nothing to do with deck length: a width that folds over the top and down both sides, and a length that runs past the front and rear of the cargo. Get those from three measurements and the rest of the specification follows.
Three measurements, in this order
- Load height — deck to the highest point of the cargo, not to the top of the trailer.
- Load width — measure the cargo, not the deck. A load that overhangs the rub rail is common and it changes the tarp width.
- Cargo length — front face to rear face, plus the overhang you want at each end.
From those three: tarp width = 2 × drop + load width, and tarp length = cargo length + overhang. Drop is load height plus one to two feet, so the hem sits below the deck edge and the wind cannot get under it.
Run it once on a typical load and the trade sizes stop looking arbitrary. An 8 ft tall, 8 ft wide load needs 8 ft of side drop each side, which gives a 24 ft width. A 24 ft cargo length plus overhang lands on 27 ft. That is a 24×27 — the standard lumber tarp, and the reason so many North American flatbed loads are covered by the same sheet.
The trade sizes, and what each one is for
Flatbed covers are sold by drop class, and the class is a description of the cargo rather than a product family. A steel tarp is not a different fabric from a lumber tarp; it is the same construction cut with a short drop, because steel sits low and the fabric only has to wrap the top corners.
| Load | Side drop | Trade size | Fabric | Why |
|---|---|---|---|---|
| Steel coil, plate, pipe | 4 ft | 24×27, 4 ft drops | 18–22 oz PVC | Low profile, but the edges are sharp and the load is dragged over |
| Machinery, mid-height cargo | 6 ft | 20×27 | 18 oz PVC | Irregular shape; corners need reinforcement more than weight |
| Lumber, plywood, building materials | 8 ft | 24×27, 8×8 drops | 18 oz PVC | Tall load, fabric dragged across board ends every trip |
| Step-deck / drop-deck | 3–5 ft | 28×16 | 18 oz PVC | Longer, narrower, lower — the opposite shape to a lumber tarp |
| Front face only | n/a | Smoke tarp, 4–8 ft deep | 18–22 oz PVC | Exhaust soot and road spray on the nose; rear already sealed |
| Dump body, aggregate | n/a | Made to body | 200–300 GSM PE | Consumable: replaced before it wears through |
Step-deck is a different shape, not a smaller one
A step-deck or drop-deck trailer carries low cargo on a long, narrow deck. The instinct is to order the same 24×27 and let the excess hang, but a long drop on a low deck is fabric with nothing to bear against: it flaps, it works the D-rings loose, and it abrades on the deck step.
Step-decks normally want the inverse proportion — longer and shallower, around 28×16, with the drop cut to the load. The other detail is the step itself. The fabric crosses a 90° change in deck height, so it needs a wear patch or a double-layer panel exactly there, not at the corners where the eye goes first.
The weight decision: 18 oz PVC or coated PE
The flatbed trade in North America settled on 18 oz (610 GSM) PVC-coated polyester in a 1000D, 18×18 or 20×20 weave, with 14 oz for light loads and 22 oz for abrasive steel. It is heavy, stiff, highly abrasion-resistant, and cold-crack resistant to about −40 °C.
Coated PE is a completely different material and should not be priced against it. Our own PE line runs 50–300 GSM. On a truck it belongs in three places, and they are real ones:
- Lorry and general cargo covers where a 50 kg sheet is unmanageable for a two-man crew.
- Dump and roll-off covers, where the fabric is a consumable and replacement cost beats abrasion life.
- Single-season and temporary covers that come off with the job.
Where it does not belong: dragged daily over coil edges, lumber ends, or a deck with rough welds. Abrasion, not sunlight, is what ends a flatbed tarp’s life.
The weight arithmetic, because it sets the price
Fabric weight ≈ area × GSM ÷ 1000. A 24×27 ft sheet is 60.2 m² of flat area. At 610 GSM the flat rectangle alone is about 37 kg. The finished tarp is heavier, because drops and hems use more fabric than the flat footprint suggests — expect 30–35 % more, so a finished 8×8-drop lumber tarp lands around 50 kg.
That number does three things at once: it tells you whether two people can handle the sheet, it sets the freight, and it converts a tonne price into a per-piece price. A 5 t order of 50 kg tarps is roughly 100 pieces. A 5 t order of 15 kg PE covers on the same footprint is over 300. Buyers who compare quotes per square metre without this step usually compare two different things.
Where the sheet actually fails
Covers rarely fail in the middle of a panel. They fail where load concentrates:
- The corner, where the drop, the hem and the webbing all meet and take load from two directions at once. It needs a patch, not just a grommet.
- The D-ring row, if the webbing is sewn to the hem rather than into it. The ring should be captured by the hem’s own stitching.
- The hem, at the point where the fabric is dragged across a load edge. A rope-reinforced or doubled hem survives a season of that; a single turn does not.
- Anywhere a fastener is punched through a plain panel. Which is why the fastening pattern matters as much as the fabric — a grommet spacing chosen for a static cover is not enough for a sheet that sees 60 mph of relative wind.
Securing: rings, grommets or a rope hem
Flatbed covers are normally built with D-rings or triangle rings along the sides, spaced to double as strap points, with grommets on the ends. The ring is the primary attachment; grommets on the same edge are for secondary ties and for lashing a partly loaded deck.
The trade convention of a hole every 24 in is a default for a cover that sits on a stack and is weighted down. A highway cover is a surface in wind, and the load per hole scales with the area each hole holds. If a tarp is going to see sustained highway speed, halve the spacing on the windward edges and specify a patch at every corner before considering a heavier fabric — the failure is at the hole, not in the cloth.
What the tarp cannot fix
A cover sheds water, controls dust and keeps cargo dry. It is not load securement: straps and chains hold the load, the tarp only sits on it. A tarp that pools water in a belly will also fatigue at that point and eventually split, so a sheet that is too wide for the load is a liability rather than a margin of safety. And where the cargo is hot — fresh asphalt, for instance — the fabric sees temperatures far above the 70 °C continuous limit of PVC, so the cover has to be quoted as a different construction rather than the standard sheet.
What to send for a quote
- Tarp size, or load height, load width and cargo length — we will do the arithmetic.
- Cargo type, because it sets weight and abrasion class.
- Trailer type, especially whether there is a step.
- Ring or grommet spacing, and where the reinforcement goes.
- Colour, if the fleet has one, and whether the sheet is branded.
Send those and we will come back with one of two answers: an 18 oz PVC spec cut to your drop, or a lighter PE sheet that suits the job — including when the honest answer is that the application needs the heavier fabric and the cheaper quote would be a mistake.


