Opens in a new tab
ROC Tarp HomepageGet a Quote

UV Resistance: How Long a Tarpaulin Actually Lasts Outdoors

About 7 min read
Share

Every supplier says their tarp is UV resistant. Almost none of them can tell you what that means numerically, because “UV resistant” is not a standard: it is a marketing phrase with no defined test, no defined exposure and no defined pass mark. What actually exists is a stabiliser package dosed into the resin, a lab test that measures how much strength is left after a fixed dose of artificial sunlight, and a set of field conditions that will defeat both.

We buy the stabiliser by the kilo and dose it into the compound, so the honest version of this page is about trade-offs rather than guarantees. It sits behind the heavy-duty range, where the stabiliser load is highest and the price difference between “one season” and “three seasons” is a number you can actually see on the quote.

What “UV resistant” physically is

Sunlight in the 290–400 nm band carries enough photon energy to break polymer chains. In polyethylene the result is chain scission: the surface oxidises, goes chalky, and loses elongation long before it loses tensile strength. That is why a sun-damaged tarp usually looks intact until you fold it, and then cracks along the fold.

The defence is an additive package, not a coating. It normally combines a UV absorber, which converts the photon energy into heat before it can break a bond, with a hindered amine light stabiliser (HALS), which interrupts the oxidation chain reaction that follows. Both are consumed as they work: the package is a finite reservoir, which is why UV life is a function of total sun dose rather than of calendar age.

The same chemistry applies to PVC, with an extra complication. PVC needs stabilisers against heat and against the hydrochloric acid it releases when it degrades, and its plasticiser migrates out over time. A PVC cover that fails in the sun often fails because the plasticiser left and the cloth went brittle, not because the polymer itself broke down.

The only comparable number is retained strength after hours

Because the phrase is unregulated, the way to compare two suppliers is to ask for the test rather than the adjective. The relevant ones are accelerated weathering under fluorescent UV lamps (ASTM G154, or ISO 4892-3 outside the US), and the usual report is:

  • initial tensile strength and elongation, warp and weft;
  • the same values after 1,000 / 2,000 / 3,000 hours of exposure;
  • the cycle used, because UVA-340 with condensation is not the same stress as UVB-313 without it.

A report that says “5 years” without hours, cycle and retention percentages is a sales document. A report that says “82% tensile retained at 2,000 h, UVA-340, 8 h light / 4 h condensation, warp direction” is a specification, and it can be compared with another supplier’s number. Ask for the second one.

Do tarps block UV? Yes — that is not the hard part

An opaque polyethylene or PVC tarp blocks effectively all UV that reaches it, which is why a tarp is a legitimate UV barrier for anything stored underneath. The hard part is different: it is whether the tarp survives the UV it absorbs. Those are two separate properties and they are routinely conflated.

Where transmission is wanted rather than blocked, an opaque tarp is the wrong product. A greenhouse needs light through the cover, so it needs a film, not a tarp; a shade structure needs partial transmission, which is what a woven leno mesh provides at roughly 70% transmission. Buying a black tarp to shade a plant nursery blocks the light entirely and cooks what is under it.

Spray-on UV treatments: what they can and cannot do

Retail UV sprays exist and some of them work on the surface they are applied to. On a tarp, their value is limited by a simple fact: the damage that matters has already happened inside the resin. A spray can slow surface chalking and reduce further attack on the outer skin, but it cannot restore elongation that has been lost, and it cannot re-dope a stabiliser package that has been consumed.

The realistic use is preventive on a cover that is otherwise sound, applied to the top surface before the first season. Applied to a tarp that already cracks along the folds, it changes nothing. If a cover has reached that stage, the fix is a heavier cloth, not a spray.

Five things that shorten life more than the stabiliser does

In field returns, the additive package is rarely the cause of early failure. These are, roughly in order of how often they show up:

  1. Flutter. A loose cover in wind flexes millions of times at the grommets and fold lines. Mechanical fatigue kills a tarp in one season that would have lasted three if it had been tensioned. This is the single largest factor and it is free to fix.
  2. Heat plus tension. A dark tarp pulled tight over a steel frame in direct sun reaches surface temperatures well above ambient. Polymer creep under that combination thins the cloth at the contact points.
  3. Pooling water. Water sitting on a sagging cover loads the low point continuously, stretches it, and (with any dust) starts biological growth that holds moisture against the cloth.
  4. Chemical contact. Fertiliser, lime, silage effluent and some oils attack the coating directly. UV resistance has nothing to do with chemical resistance, and a UV-stabilised tarp can fail in one season on a lime pile.
  5. Folding on the same line every time. Repeated creases at the same point are where cracking starts. Storing a large cover rolled rather than folded adds seasons for free.
What you see What it usually is What actually helps
Chalky white surface, colour washed out Surface oxidation — the stabiliser is being consumed Nothing retroactive; expect cracking at folds next
Cracks along fold lines only Flex fatigue plus lost elongation Roll instead of fold; heavier cloth next order
Torn holes at grommets, cloth intact Flutter and point loading, not UV More tie points, tighter tension, reinforcing patches
Stiff cloth that snaps when bent Plasticiser loss (PVC) or advanced oxidation (PE) Replace; not repairable
Green or black growth on the underside Moisture held against the cloth Airflow and drainage; biological, not UV

What we will and will not put in writing

What we will state on a quote: the base polymer, the GSM, the stabiliser package as a class (standard or high-load), and — on request, for a specific order — the accelerated weathering data for that construction with the test cycle named.

What we will not state is a service life in years. Any number would be a guess about your sun hours, your wind, your tension and your handling, and a guess that gets written into a purchase order becomes a claim. Buyers who need a defensible figure for a tender should specify the test rather than the duration: “80% tensile retained at 2,000 h per ASTM G154” is a requirement a supplier can be held to, and it is the form in which UV performance is actually procured.

If the choice is between a heavier cloth at the same stabiliser load and a lighter cloth at a higher load, take the heavier one for anything that will flutter, and the higher load for anything static in strong sun. That is the trade-off, and it is the only part of this subject where the answer is consistent across materials.

roctarp.com

Ready to start your project?

Bring your drawing and the requirements you want to review.

  • Drawing
  • Material
  • Quantity
Request a quote
PROJECT INQUIRY

Ready to start your project?

By submitting this form you agree to be contacted about your enquiry.

Leading PE tarpaulin factory in China. Specialized in manufacturing high-quality polyethylene tarpaulins.

  • what'sapp: +86 18561818308marketing@roctarpstarp.com
  • Get an instant quote