Most shade enquiries arrive as a feeling rather than a number: some shade over the patio, enough to stop the cars cooking, something over the kennel run. The first job here is to turn that into a shade factor, because shade factor is the only figure that decides which fabric you are being sold. The second job is to be straight about the one factor we make.
1. What shade factor actually measures
Shade factor is the share of daylight a fabric blocks. A 30% shade cloth passes about 70% of the light and blocks the rest; a 90% cloth passes about a tenth. It says nothing about weight, thickness or strength. On an open fabric those are separate decisions, and a heavier yarn in the same grid gives you a coarser net, not a darker one.
Two things follow that surprise people on site:
- Shade is not cooling. A panel blocks direct sun and the radiant heat that rides with it. It does not lower air temperature. Under 30% shade on a still day the difference is real but modest – it is the difference between standing in sun and standing in broken light, and the air keeps moving through either way.
- Shade is not privacy. At 30% coverage you can see through the panel from a few metres and read shapes through it at ten. Screening a yard from a neighbour is a denser product and a different conversation.
2. What the usual jobs are normally specified at
This is the comparison we would draw on a whiteboard. The second column is what the market quotes for each job. The third is the honest answer at 30%.
| Where it hangs |
Normally specified |
Is 30% enough? |
What we supply |
| Patio, deck, pergola |
50-70%, knitted |
Usually – shades the table without making the room dark |
Panel with eyelets or a rope edge |
| Car park, yard, forecourt |
50-80% |
Yes, and it takes wind better than a solid sheet |
Panel or roll, corners reinforced |
| Plant nursery, polytunnel |
50-70% for most stock |
For light-loving stock; not for deep-shade crops |
Roll or unhemmed cut panel |
| Livestock pen, kennel run |
70-90% |
Yes for airflow, short of full shade |
Panel, eyelets at 12 in centres |
| Playground, school yard |
70-90% |
Yes, where the frame is already fixed |
Panel with corners reinforced |
| Hot-climate greenhouse |
60-90% for heat control |
No |
Nothing – that is knitted, and we say so |
Read the third column and the boundary draws itself: above roughly 30% the market moves to warp knitting, and we do not knit. Below it, a woven grid has properties knitting cannot copy – it cannot ladder from a snag, it holds its shape in wind, and a cut edge does not come apart. The weaving side of that argument belongs on the leno mesh page, because it is a question about construction rather than shade.
3. Why patios and car parks so often come back to 30%
Patio shade is the biggest single use of this fabric, and the reason is not price. It is that a solid roof over a seating area turns the space under it into a trap: radiant heat comes off the underside, air stops moving, and by mid-afternoon the shaded table is the least comfortable place in the garden. An open panel blocks the sun before it reaches the ground and lets the air through, so what arrives underneath is light and moving rather than hot and still.
Car parks and forecourts behave the same way at larger scale, with two extra gains. A 30% panel lets a driver see through it, which matters when the panel is the only thing between a reversing truck and a walkway. And because most of the wind passes through the grid rather than loading it, the panel survives the first real gust where a solid sheet on the same frame is torn off at the eyelet line.
The practical limits are worth stating before anyone orders. Hang it high – 2.4 m or more above the surface you want shaded – because a low panel shades a narrow strip and blocks the view. Give it a fall so water runs off rather than pooling on the low side. And fix it to something that already exists; we supply the panel and its edge, not a frame.
4. Nurseries, livestock and kennels
Where something alive is underneath, 30% stops being a compromise and becomes the correct answer. Seedlings and leafy stock need light to keep growing; a 70% cloth over a propagation bench slows them down and stretches them. A livestock pen needs air more than it needs darkness – cattle and dogs shed heat through breath and hide, and a closed roof over a pen produces a hot box that animals avoid. A 30% panel cuts the direct sun, keeps the flies off the worst of it and leaves the air moving.
Kennel runs and poultry pens are the same logic at small scale, and they are where eyelet spacing earns its money: a dog leaning on the panel or a bird flying at it puts a point load on the nearest ring. Corners get reinforcement, and 12 in centres along the exposed edge is what we would specify rather than 24 in.
Playground and school-yard shade is usually specified much darker, and there we are honest: if the requirement is written as 70% or 90%, it is knitted shade cloth and it is not ours. What we can do is the panel, its edge and its fixings at 30%, on a frame that the school or the contractor already has.
5. Triangles, sails and how the panel is actually hung
Triangular shade is a large part of this market and it is a shape we can cut: a triangle is a cutting job, and we cut, eyelet and reinforce the corners to your dimensions. What we do not supply is the rest of the system. A shade sail is an engineered assembly – anchor points rated for the load, tensioned cable or turnbuckles, and a frame or wall that can take the pull. We make the fabric panel; the hardware belongs to a specialist, and pretending otherwise is how sails end up on the ground after a storm.
Because a triangle has no straight edge to run a rope along, the corners carry everything. Every triangle we cut gets a reinforced corner at each point, and the eyelet is set through the reinforcement rather than through the cloth. If you are finishing the panel yourself, the same rule applies: put a patch or a folded corner under every fixing, or the first hard gust will pull the ring out and the tear will run.
For rectangular panels there are three ways to hang them, and the choice changes the price:
- Eyelets at the perimeter, 24 in as a working default and 12 in on exposed or long edges, with corners reinforced as standard.
- A rope edge – a pocket formed along the hem that a rope or cable runs through. On a large panel this spreads load along the whole edge instead of at a few rings, and it is the stronger fixing of the two.
- Tied through the mesh, which works for light temporary shade and is the cheapest, because it needs no finishing at all.
Tell us the fixing method rather than the eyelet count and we will set the spacing to it. Spacing is a load decision, not a habit.
6. Where 30% is the wrong answer
Four cases come up often enough to name:
- You need dry underneath. An open grid passes rain almost as freely as it passes air, so a shade panel is not a roof. This is the single most common mismatch in the category, and the phrase to be careful with is “waterproof shade tarp” – the two words do not describe the same fabric. If the requirement is dry, the answer is a solid cover, and the waterproof range is where that argument is set out properly.
- You need it genuinely dark. Blackout, projection, light-sensitive storage: 90% and above, knitted, not us.
- You need a privacy wall. 30% is see-through at close range. For a boundary screen, privacy screening is the right page.
- You need the air cooler. Shade cuts radiation, not temperature. A panel plus airflow is the combination that works; a panel alone in still air disappoints everyone.
The build that solves the exposed-site version of this is two layers, not one: a solid cover underneath for the water, and a shade panel over the top to take the wind and the UV. Each does the job the other cannot, and neither is asked to be something it is not.
7. Ordering shade cloth by the tonne
We sell to the trade: distributors, shade and landscape contractors, and brands that put their own label on the panel. Minimum order is 5 tonnes, and 5 tonnes per specification for a custom colour or width – specifications do not combine. Because this fabric is light, five tonnes is a high piece count rather than a few heavy rolls, so we quote the piece weight next to the price and the arithmetic is visible before you commit.
Lead time is about 30 days for a container of standard white or green. Samples are free and you cover the courier – ask for a cut piece rather than a swatch card, because on an open fabric you want to hold it against the light, not look at a 10 cm square on a desk.
Format matters more than size on this product. A finished panel is cut, edged and eyeleted; a roll is full width and continuous; a cut panel is cut to size with no finishing, for fabricators who finish on site. Sizes are cut to order with no tooling, so a non-standard size costs the same per square metre as a standard one – what changes the price is the finishing, not the dimensions.
For the weaving itself, the cutting and sealing floor and the eyeleting and hem line show where the panel is made. Where the shade goes over crops or stock, the greenhouse and garden and landscape ranges put it in context, and rolls are ordered through tarpaulin rolls.