Opens in a new tab
ROC Tarp HomepageGet a Quote

SPECIFICATIONS · TARPAULIN SIZES

Tarpaulin sizes: the chart, and what each number changes.

A size is not one number. It is a covered area, a made width, a weight and a seam plan, and changing any of the four changes the price before it changes anything you can see. Everything below is measured, not estimated.

The four numbers that set a price.

Covered size — the surface, plus overhang and tie-down

Made width — PE tops out at 4.0 m in one pass, PVC at 5.0 m

Weight — PE 50–300 GSM, PVC 475–745 GSM (18–22 oz)

Seams — every join is a weld, and every weld is a future leak

Any supplier who quotes a size without asking for the other three is quoting a guess.

What a “10 × 10 tarp” actually measures.

This is the single most common misunderstanding in the category, and it costs buyers real money. Two tarps sold as 10 × 10 can differ by four inches across, because the trade uses two different measuring conventions.

Cut size

The size the fabric was cut to, before hemming. A retail pack marked “cut size” is typically 4–6 in larger than the tarp inside it.

Finished size

Measured across the outer edge after hem and eyelets. This is the number that matters on site, because it is what you actually get.

How we quote

Finished size, hem and eyelet included, stated on the specification sheet. Ask any supplier which of the two they mean before you compare prices.

Our sizes are welded, not sewn. That matters for size as well as strength: a sewn hem draws the panel in as the needle runs, so the finished article drifts shorter. A heat-welded hem does not move, which is why the size on our sheet is the size that arrives.

Every size we quote, in feet and metres.

Sizes below are finished sizes. The weight column is what we would actually propose for that size — not the whole range we can make. A 6 × 8 at 300 GSM exists, it is simply not what the job asks for.

Small — 6 × 8 to 10 × 12 ft

Under 120 sq ft. Where weight matters more than span, because one person handles it.

Size (ft)Size (m)Area sq ftArea m²Typical jobWeight we would quote
6 × 81.83 × 2.44484.5Firewood, sandpit, small trailer load50–150 GSM
8 × 82.44 × 2.44645.9Pallet cover, ground sheet50–150 GSM
8 × 102.44 × 3.05807.4Single pallet stack, garden tidy80–180 GSM
10 × 103.05 × 3.051009.3Van load, small shed roof, market stall120–200 GSM
10 × 123.05 × 3.6612011.1Carport bay, small boat, wood store150–200 GSM

Medium — 12 × 16 to 16 × 20 ft

120 to 320 sq ft. The band where wind load starts to decide the eyelet spacing rather than the cover.

Size (ft)Size (m)Area sq ftArea m²Typical jobWeight we would quote
12 × 123.66 × 3.6614413.4Gazebo footprint, hot tub, small run150–200 GSM
12 × 163.66 × 4.8819217.8Garage roof, trailer bed180–220 GSM
12 × 203.66 × 6.1024022.3Single garage, 20 ft container mouth200–250 GSM
12 × 243.66 × 7.3228826.8Long trailer, large log store200–250 GSM
16 × 204.88 × 6.1032029.7Double carport, small barn roof200–250 GSM

Large — 20 × 20 to 24 × 36 ft

400 to 864 sq ft. This is where trailer and lumber covers live, and where a seam every 4 m becomes a design constraint.

Size (ft)Size (m)Area sq ftArea m²Typical jobWeight we would quote
20 × 206.10 × 6.1040037.2Roof section, silage stack end180–250 GSM
20 × 306.10 × 9.1460055.7Flatbed and step-deck, hay stack200–300 GSM
20 × 406.10 × 12.1980074.340 ft container, pool, event floor200–300 GSM
24 × 247.32 × 7.3257653.5Barn bay, machine storage200–300 GSM
24 × 367.32 × 10.9786480.3Lumber and steel loads250–300 GSM

Extra large — 30 × 30 ft and beyond

900 sq ft and up, including roll lengths. Above about 20 m across, the number of welds — not the weight — is what limits the design.

Size (ft)Size (m)Area sq ftArea m²Typical jobWeight we would quote
30 × 309.14 × 9.1490083.6Whole roof pitch, machinery park250–300 GSM
30 × 409.14 × 12.191,200111.5Shed span, silage clamp250–300 GSM
40 × 6012.19 × 18.292,400223.0Yard cover, staging, bulk ground sheet250–300 GSM
24 × 1007.32 × 30.482,400223.0Silage bunker run, greenhouse blackout200–250 GSM
32 × 1009.75 × 30.483,200297.3Long bunker, windbreak line200–250 GSM

A 40 × 60 and a 24 × 100 are both 2,400 sq ft. They are not interchangeable: the shape decides how many welds each one carries.

GSM, ounces and mils are three different measurements.

Buyers arrive with whichever unit their last supplier used. None of them converts cleanly into the others without knowing the polymer, and that is where specifications quietly go wrong.

Ounces to GSM

Ounces per square yard is the PVC convention. Multiply by 33.9 to reach GSM.

oz/yd²GSMWhere it sits
10 oz339 GSMLight retail covers, dust sheets
12 oz407 GSMGeneral PVC covers
14 oz475 GSMBottom of the PVC range we supply
15 oz509 GSMTruck and trailer
16 oz542 GSMHeavy flatbed, lumber
18 oz610 GSMLumber tarps, deck covers
20 oz678 GSMMarine and hatch covers
22 oz746 GSMTop of the PVC range we supply

Mils to GSM — and why the column splits

A mil is a thickness, not a weight. The same 15 mil is 358 GSM in PE and 507 GSM in PVC, because PVC compound is about 1.33 g/cm³ against PE at 0.94.

ThicknessPE @ 0.94PVC @ 1.33
3 mil72 GSM101 GSM
4 mil96 GSM135 GSM
5 mil119 GSM169 GSM
6 mil143 GSM203 GSM
8 mil191 GSM270 GSM
10 mil239 GSM338 GSM
12 mil287 GSM405 GSM
15 mil358 GSM507 GSM
18 mil430 GSM608 GSM
20 mil478 GSM676 GSM

PE stops at 300 GSM, which is about 12.5 mil — a 15 mil PE does not exist in our range, whatever a converted data sheet says.

PVC starts at 475 GSM (14 oz) and stops at 745 GSM (22 oz). Below 14 oz the coating is thin enough that the scrim shows through under tension.

Grams per square metre is the only unit that survives a change of polymer, which is why our specification sheets are written in GSM first.

Width decides how many welds a cover carries.

This is the part of a size that almost never appears on a quotation. Our PE is formed at 2.0 m and 4.0 m in a single pass; PVC at 3.2, 4.0 and 5.0 m. Anything wider is panels welded together, and each weld is a line where a cover can eventually fail.

Finished widthIn yardsPE panelsPE weldsPVC panelsPVC welds
6 m6.6 yd2121
10 m10.9 yd3221
12 m13.1 yd3232
20 m21.9 yd5443
30 m32.8 yd8765
40 m43.7 yd10987

Why it is not just arithmetic

A weld is a heat-sealed overlap. It carries less load than the sheet around it, so a 30 m span with seven welds needs either a heavier cloth or a shorter seam plan — sometimes both.

What we do about it

We lay the panels so seams run along the low side of the cover, not across the middle of a span. That is a drawing decision, made before cutting.

What it means for you

If your cover is over 12 m across, expect the weld count to be quoted alongside the size. If it is not, ask.

What is on the floor right now.

Eighteen finished specifications, each with at least one size in stock as a standard run. These are the sizes you can order without a new cutting plan. Everything else we make is cut to your size.

SKUMaterialWeightFinished sizeColourAlso filed under
rt-pe200-ss-2030PE200 GSM20 × 30 ft (6.1 × 9.1 m)Silver / SilverPE
rt-pe300-bk-2436PE300 GSM24 × 36 ft (7.3 × 11.0 m)BlackHeavy duty
rt-pe220-sy-2030PE220 GSM20 × 30 ft (6.1 × 9.1 m)Silver / YellowRoofing
rt-pe250-wh-2040PE250 GSM20 × 40 ft (6.1 × 12.2 m)WhiteCanopy
rt-pe200-bl-2040PE200 GSM20 × 40 ft (6.1 × 12.2 m)BluePool
rt-pe200-sb-32100PE200 GSM32 × 100 ft (9.8 × 30.5 m)Silver / BlackSilage
rt-pe200-bk-24100PE200 GSM24 × 100 ft (7.3 × 30.5 m)BlackGreenhouse
rt-pe180-wh-1220PE180 GSM12 × 20 ft (3.7 × 6.1 m)WhiteCarport
rt-pe150-gn-6x50PE150 GSM6 × 50 ft (1.8 × 15.2 m)GreenFence
rt-pe150-bk-6x300PE150 GSM6 × 300 ft roll (1.8 × 91 m)BlackGround cover
rt-cm150-wd-2030PE150 GSM20 × 30 ft (6.1 × 9.1 m)Woodland camoCamo
rt-pe200-ss-m4x50PE200 GSM4 × 50 m roll (13.1 × 164 ft)Silver / SilverRolls
rt-pvc18-bk-2427PVC18 oz / 610 GSM24 × 27 ft + 8 × 8 ft dropsBlackLumber
rt-pvc18-bk-2030PVC18 oz / 610 GSM20 × 30 ft (6.1 × 9.1 m)BlackPVC
rt-pvc18-wh-20ftPVC18 oz / 610 GSMSuits a 20 ft open-top containerWhiteContainer
rt-pvc22-bk-3040PVC22 oz / 745 GSM30 × 40 ft (9.1 × 12.2 m)BlackMarine
rt-hd250-bk-2030HDPE250 GSM20 × 30 ft (6.1 × 9.1 m)BlackHDPE
rt-le-cl-m2x50Leno~70% light pass2 × 50 m rollClearMesh

Stock moves. A size listed as a standard run still needs to be confirmed against the current production slot before it goes on a purchase order.

If your size is not on the list.

Most of what we ship is not on the list. The list is the stock programme; the business is made-to-size, and the only thing that changes is the specification step.

01

Send the covered size

Not the tarp size — the surface plus the overhang you want and where it ties down. A photo with a tape measure in it beats a description.

02

We return a weight and a width

Which GSM holds that span, which made width gets you the fewest welds, and where the seams will land.

03

Sample, then the run

A laminate swatch is free, freight at your end. Production follows the approved swatch, not the drawing.

04

Five tonnes per specification

Sizes within one specification can be mixed inside the 5 t. A change of weight or colour starts a new specification.

What we do not do

Sewn hems, webbing loops, zip openings — those are stitched downstream

Drainage fittings, elastic edges, rope-reinforced hems

Retail packing, hang tags, barcode labels

Orders under 5 t per specification, or single-piece retail

Saying this up front saves both sides a week. If your process needs any of the above, plan it on your side of the container and we will cut to suit.

Questions that come up before the first order.

Is a 10 × 10 tarp really 10 × 10 ft?

Only if it is sold as a finished size. Retail packs often quote cut size, and the hem takes 2–3 in off each side, so the tarp inside measures closer to 9 ft 6 in. Ask which convention a supplier uses before comparing two quotes.

What is the biggest tarpaulin size you make?

Width is limited by the made width and the weld plan, not by a maximum size. PE forms at 4.0 m in a single pass, PVC at 5.0 m; beyond that we weld panels. Covers of 30 m across are routine. The practical limit is handling weight, not the loom.

How much does a 20 × 30 tarp weigh?

At 200 GSM, a 20 × 30 ft cover is 55.7 m² and weighs about 11.1 kg before eyelets and packing. At 300 GSM it is about 16.7 kg. That is the point where one person stops being able to handle it on a roof.

What size tarp covers a 20 ft container?

The opening is 20 ft × 8 ft, so a 20 × 30 ft sheet gives a 5 ft drop over each long side, or 20 × 40 ft if you want the ends covered as well. PVC at 18 oz is the usual choice because it does not flap itself apart in wind.

Can I order one tarp in a custom size?

Not at retail quantity. The minimum is 5 t per specification, and a single 20 × 30 at 200 GSM is about 11 kg — so 5 t is roughly 450 pieces of that one size. Sizes inside the specification can be mixed to reach the 5 t.

Do you convert inches to centimetres on the sheet?

Sizes are stated in feet and metres, because those are the two units our buyers order in. Inches appear only where a customer's own drawing uses them. 1 ft = 0.3048 m, and every figure above is converted from that, not rounded by hand.

SEND THE COVERED SIZE

Send the surface. We will send the weight.

Tell us what the cover sits over, the span it has to cross and how it ties down. What comes back is a weight, a made width and a seam plan — in writing, with the tolerance stated.

Leading PE tarpaulin factory in China. Specialized in manufacturing high-quality polyethylene tarpaulins.

  • what'sapp: +86 18561818308marketing@roctarpstarp.com
  • Get an instant quote